The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.

Specifications:

• Material: 6061-T6 Aluminum
• Thickness - 3mm
• Width - 8mm
• Length - 336mm
• Step File

The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.

Specifications:

• Material: 6061-T6 Aluminum
• Thickness - 3mm
• Width - 8mm
• Length - 384mm
• Step File

The Studica Flat Beam is 3mm thick and 8mm wide. As with the other Studica Robotics building components, it has the common hole pattern which makes it easy to connect to other structure with very little or no additional machining required. You can easily connect to other channel, extrusions, bushings, bearing, mounting brackets and more so you can quickly assemble and disassemble robots and automated systems.

Specifications:

• Material: 6061-T6 Aluminum
• Thickness - 3mm
• Width - 8mm
• Length - 432mm
• Step File

The Servo Power Block is a 6V, 60W power injector that provides proper power for RC Servos. It does not interfere with the signal, it will only replace the power to the servo with 6V. 

Features,

• Built in DC-DC converter
• Over-current shutdown
• ESD protection

Specifications,

• Nominal Input Voltage: 12V
• Operational Voltage Range: 6.0V
• Number of Channels: 8
• Max Current for All Channels Combined: 10A
• Total Continuous Power: 60W
• Size: 70mm x 45mm x 16mm
• Step File

Use it to power the Studica Smart Robot Servo Programmer or any other device requiring 6V output and a TJC8 connector. 

Specifications:

• 6V Output
• On/Off Power switch
• TJC8 connector
• Uses 4 x 1.5V AA Batteries (not included)

Use the Dupont Single Pin - 4 wire - female to female cable with the Ultrasonic Distance Sensor

Specifications: 

• Dupont Single Pin
• 4 wire
• female to female cable
• Length: 50cm
• Gauge: 22AWG

This set of 12 pieces includes,

• 2 x 20cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
• 2 x 40cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
• 2 x 60cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
• 6 x 3pin Dupont male to male connectors

The Studica MD2 is a next-generation high performance Motor Controller Driver and Sensor Adapter with many added features to make it ready to use in your robot project. The included VNH5019ATR-E Motor Controller ICs are very robust with high current output and several important protection features. Many other I/O options have been incorporated into this design to make it extremely easy to interface to several different sensors.

Features,

• Includes 2 VNH5019 Motor Controller ICs,
  • 2 Enable Inputs, 2 direction inputs, one PWM input per channel up to 20Khz
  • Up to 12A Continuous output per channel, 30A peak current short ms duration
  • Under-voltage, over-voltage, reverse-voltage protection
  • Thermal Shutdown protection
  • Current Limit protection
  • Current Sense Output Proportional to Motor Current (approx. 140 mV/A)
  • Loss of Ground and Loss of Vcc Protection
  • Protection against short to Ground and short to Vcc

Specifications,

• 3V-compatible inputs
• Directly interfaces with myRIO MXP Port
• 8-16V DC Battery Input Terminal, J7, (GND, MTRS+ PWR)
• Jumper Selectable Current sense feedback from the VNH5019 Motor ICs, J12, J17
• Reverse Power LED Indicator
• FWD and REV Motor Direction LED Indicators
• 3 Servo Headers, J9, J10, J11, (SIG, SVDC, GND)
• 1 Parallax Ping Sensor Port, J13, (GND, VCC, DIO)
• 1 Sharp IR Port, J21, (AI0, VCC, GND)
• 1 LSB Port, J18, (VCC AI0, AI1, AI2, AI3, GND)
• 1 Nav-X Port, J19, (VCC, SDA, SCL, GND)
• 2 Encoder Ports, J22, J23, (VCC, ENCB, GND, ENCA)
• 1 I2C Port, J20, (NC, SCL, SDA)
• Built in 5V 3A voltage Regulator
• 3.3V Power Rail Header, J3, from myRIO
• 5V Power Rail Header, J4, from onboard regulator
• GND Rail Header, J6
• Separate Servo Power Input, J8 (SV+ PWR, GND)

Studica Blackhawk Expansion Board is a programmable expansion add on  for your myRIO project. The board is used with the Studica MD2 driver board and the NI myRIO to control servo motors and to add additional sensor expansion and I/O including limit switches and relays. 

Note:

• Requires Studica MD2 Driver Board and NI myRIO with LabVIEW and StudicaToolkit

The Studica Robotic Expansion Board features:

• 5V - 3A Servo power that supports to 2 additional servos
• 5V - 5A additional power output
• 5V and 12V FPV camera power
• Dedicated myRIO and Radio power ports to power both devices easily
• 3 Digit Voltmeter to give the current battery voltage
• Reverse Voltage Protection
• 3 on board Relays, 1 of the Relays can be changed into a timed switch for an indicator light by flipping the switch next to the relay to enable the timer.
• Arduino like Microcontroller on board to give sensor feedback to the myRIO
• 4 Sharp Sensor ports
• 2 Studica Line Follower Sensor ports
• 16 Pulled high Limit Switch ports
• Arduino 1.0 Header
• Superfast 84 MHz speed
• Dedicated I2C header to plug directly into the I2C header of the MD2 board

Power Switch Plate for Power Switch # 70183

The JST-GH to JST-GH Cable connects external sensors, breakout boards or other devices.

Detailed Specifications:

• Cable Length: 25 cm
• Connectors: 4-pin JST-GH (2)
• Wire Colors: Black, Red, Blue, Green

The VMX Battery Adapter cable connects a VMX-pi power connectcor to an external battery supply.

Detailed Specifications:

• Cable Length: 25 cm
• Wire Gauge: 20 AWG
• Connector: JST-VH Wire Colors: Red (power), Black (ground)
• Wire Free-end:  stripped and tinned

The VMX Wallwart Barrel Plug Adapter cable connects a VMX power connector to an external 12VDC Wallwart power supply.

Detailed Specifications:

• Cable Length: 25 cm
• Wire Gauge: 20 AWG
• VMX-side Connector: JST-VH Wire Colors: Red (power), Black (ground)
• Wallwart-side Barrel Plug Connector:  2.1mm inner diameter, 5.5" outer diameter, center-positive

<p>The VMX GH-to-SH breakout board connects a 4-pin .1" standard connect (sometimes referred to as an "AMP connector").&nbsp; The connector may either be a standard or a locking variety connector.
</p>
<ul>
<li>Board Dimensions:&nbsp; 2" x .75" x .15"</li>
<li>VMX-side Connector: JST-GH Connector, 4-pin</li>
<li>External Connector:&nbsp; AMP Male Connector w/support for locking tab (4-pin)</li>
</ul>

The Titan Cable Pack contains three cables. A 60cm CAN Wire for connecting the Titan Motor Controller to a CAN 2.0B capable device and two (idk the 50cm JST-VH to JST-VH cables for connecting 12VDC power to other devices such as the VMX or Servo Power Block.

• 2 - JST-VH to JST-VH cable
  • 50cm
• 1 - CAN Wire
  • 60cm

Used to replace or supplement connector on NI myDAQ Kit

Includes:

• 70177 - 4 JST-GH to 4 Pin Dupont Cables (connects a VMX-pi GH signal connector to an external sensor or device). 
• 70167 - 1 battery adapter cable (connects a VMX-pi power connector to an external battery supply).
• 70166 - 1 Wallwart cable (a Barrel Plug Adapter cable allows you to connect a VMX-pi to an external 12VDC Wallwart power supply).

ThePowerpole Crimp Tool 15, 30, 45 crimping tool provides a positive crimp on the 15, 30 & 45 amp contacts manufactured by Anderson Power Products for the Powerpole® line of products. It has the following features.

Specifications:

• Crimps all three sizes of Powerpole® contacts; 15, 30 and 45 amp
• Built-in contact positioner that holds the contact during crimping
• Ratchet mechanism assures proper crimps every time
• Far faster and better than soldering
• Provides the highest strength and the lowest resistance connections possible
• Dimensions: 7.75" X 3" X 1.5"
• Weight: 20 ounces
• High Contact retention force

Contacts & Jaw Position

The 3 contacts have different amp ratings:

• 15 Amp (SKU: 1332) is designed to receive 16, 18 and 20 gauge wire.
• 30 Amp (SKU: 1331) is designed to receive 12, 14 gauge wire.
• 45 Amp (SKU: 261G2) is designed to receive 10 gauge wire.

The contact size corresponds to the position marking on the die. The 15 amp contact goes into the 15 amp position, the 30 amp into the 30 position, and 45 amp into the 45 position.

Assembly Instructions 15 & 30 Amp

To crimp the 15 & 30 amp contacts it is recommended that you insert the wire into the contact prior to inserting them into the tool. Then, with the flat side of the contact down, insert the contact tip into the proper slot for crimping.

Squeeze the ratchet handle until the ratchet mechanism releases. Do not over crimp by squeezing the handles together until they touch, it is possible to break the die.

Assembly Instructions 45 Amp

To crimp the 45 amp contact it is recommended that you position the tip of the 45 amp contact into the 45 amp position slot before the wire is inserted. Make sure the contact is properly positioned with the U (open contact) facing up. If the contact is lying sideways you may not obtain a proper crimp. Then, insert your wire into the inserted contact.

Squeeze the ratchet handle until the ratchet mechanism releases. Do not over crimp by squeezing the handles together until they touch, it is possible to break the die.

Read more: http://www.powerwerx.com/crimping-tools/tricrimp-crimping-powerpole-contacts.html#ixzz2YlrFRGU8

Note: Only official tooling solutions recommended by APP may be acceptable for safety agency approvals such as UL, CSA and TUV. Official tooling solutions such as the 1309 series are available for purchase at a higher price. Read more: http://www.powerwerx.com/crimping-tools/tricrimp-crimping-powerpole-contacts.html#ixzz44INkWK9m

Studica First Person View (FPV) System for WorldSkills Mobile Robotics.

Featuring a Small lightweight video transmitter, 650TVL Camera with 2.8mm Wide angle lenses, and a 7-inch LCD HD screen.

MAIN FEATURES

• LCD
  • Small and lightest video transmitter
  • 5V-22V input
  • 25mW / 200mW power settings
  • Ultra-clean transmission
  • Robust RF amplifier
  • Clean powerup and video switching
  • LCD screen feature integrated 5.8Ghx Dual Diversity Receiver and automatic signal search (Supports 40 channels)
• Camera
  • "Zero" latency (less than 1ms end to end)
  • 650 TVL - the highest possible resolution without adding additional latency
  • Tuned both for day and night flying
  • 2.8mm wide angle lens
  • Lightweight plastic enclosure, matching popular older cameras for mounting compatibility
  • Wide voltage input range (5V - 22V)
• 5G8 MMCX Linear Antenna with MMCX connector
• UNIFY PRO 5G8 HV Video Transmitter
  • ​Smallest, lightest video transmitter on the market
  • 2-6S input power supported
  • 25mW / 100mW / 400mW power settings
  • Integrated heat sink
  • Ultra-clean transmission (up to 16 pilots at once!)
  • PitMode - power up your quad during a race
  • Easy OSD, FC and RC channel changes, with fallback button menu
  • Robust RF amplifier allows powering up without antenna for hours!
  • Clean powerup and video switching
• CE certified

The Powerpole Extension Cable is 50cm long and 14AWG wire gauge to handle heavier loads.

Ideal for the myRIO.

• Inside Contact Diameter: 2.1mm
• Outside Contact Diameter: 5.5mm
• Termination Style: Solder Cup
• Voltage Rating: 12 V
• 6 Amp
• 1 meter cord length
• 18AWG or 20AWG wire guage
• DC connector type

Ideal for the myRIO.

• Inside Contact Diameter: 2.1mm
• Outside Contact Diameter: 5.5mm
• Termination Style: Solder Cup
• Voltage Rating: 12 V
• 6 Amp
• 1 meter cord length
• 18AWG or 20AWG wire guage
• DC connector type