150mm Blue Zip Tie, 100 pack, can be used for wire management.

Specifications:

• Length: 150mm
• Material: Nylon
• Quantity: 100pcs

150mm Blue Zip Tie, 100 pack, can be used for wire management.

Specifications:

• Length: 150mm
• Material: Nylon
• Quantity: 100pcs

Use the Dupont Single Pin - 4 wire - female to female cable with the Ultrasonic Distance Sensor

Specifications: 

• Dupont Single Pin
• 4 wire
• female to female cable
• Length: 50cm
• Gauge: 22AWG

The Studica Analog Module

• Includes JST-SH to JST-GH Cable
• Operating Voltage (VDD): 2.0V-5.5V
• Operating Temperature: -40°C to 125°C
• Operation Modes: Single-Shot, Continuous-Conversion (Default), and Duty Cycling
• Analog Inputs:
  • Measurement Type: Single-Ended (Default)
  • Input Voltage Range: GND to VDD
  • Full Scale Range (FSR): ±.256V to ±6.114V (Default: 2.048V)
• Resolution:
  • 12-bit (Differential) or 11-bit (Single-Ended)
  • LSB size: 0.125mV - 3mV (Default: 1 mV)
• Sample Rate: 128 Hz to 3.3 kHz (Default: 1600SPS)
• Current Consumption (Typical): 150μA-200μA
• I2C Address: 0x48 (Default), 0x49, 0x4A, or 0x4B
• Four unique I2C addresses:
  • 0x48
  • 0x49
  • 0x4A
  • 0x4B
• Step File

USB Cable, Type A to Type C, Blue, 1 Meter, male to male

The JST-GH to JST-GH Cable connects external sensors, breakout boards or other devices.

Detailed Specifications:

• Cable Length: 25 cm
• Connectors: 4-pin JST-GH (2)
• Wire Colors: Black, Red, Blue, Green

The VMX Battery Adapter cable connects a VMX-pi power connectcor to an external battery supply.

Detailed Specifications:

• Cable Length: 25 cm
• Wire Gauge: 20 AWG
• Connector: JST-VH Wire Colors: Red (power), Black (ground)
• Wire Free-end:  stripped and tinned

The VMX Wallwart Adapter cable connects a VMX power connector to an external 12VDC Wallwart power supply.

Detailed Specifications:

• Cable Length: 25 cm
• Wire Gauge: 20 AWG
• VMX-side Connector: JST-VH Wire Colors: Red (power), Black (ground)
• Wallwart-side Connector:  2.1mm inner diameter, 5.5" outer diameter, center-positive

<p>The VMX GH-to-SH breakout board connects a 4-pin .1" standard connect (sometimes referred to as an "AMP connector").&nbsp; The connector may either be a standard or a locking variety connector.
</p>
<ul>
<li>Board Dimensions:&nbsp; 2" x .75" x .15"</li>
<li>VMX-side Connector: JST-GH Connector, 4-pin</li>
<li>External Connector:&nbsp; AMP Male Connector w/support for locking tab (4-pin)</li>
</ul>

The Titan Cable Pack contains three cables. A 60cm CAN Wire for connecting the Titan Motor Controller to a CAN 2.0B capable device and two (idk the 50cm JST-VH to JST-VH cables for connecting 12VDC power to other devices such as the VMX or Servo Power Block.

• 2 - JST-VH to JST-VH cable
  • 50cm
• 1 - CAN Wire
  • 60cm

Used to replace or supplement connector on NI myDAQ Kit

Includes:

• 70177 - 4 JST-GH to 4 Pin Dupont Cables (connects a VMX-pi GH signal connector to an external sensor or device). 
• 70167 - 1 battery adapter cable (connects a VMX-pi power connector to an external battery supply).
• 70166 - 1 Wallwart cable (cable allows you to connect a VMX-pi to an external 12VDC Wallwart power supply).

Ideal for the myRIO.

• Inside Contact Diameter: 2.1mm
• Outside Contact Diameter: 5.5mm
• Termination Style: Solder Cup
• Voltage Rating: 12 V
• 6 Amp
• 1 meter cord length
• 18AWG or 20AWG wire guage
• DC connector type

Ideal for the myRIO.

• Inside Contact Diameter: 2.1mm
• Outside Contact Diameter: 5.5mm
• Termination Style: Solder Cup
• Voltage Rating: 12 V
• 6 Amp
• 1 meter cord length
• 18AWG or 20AWG wire guage
• DC connector type

This set of 12 pieces includes,

• 2 x 20cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
• 2 x 40cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
• 2 x 60cm 22AWG Cables with Dupont TJC8 2.54mm 3 pin, female to female connectors
• 6 x 3pin Dupont male to male connectors

The Powerpole Extension Cable is 50cm long and 14AWG wire gauge to handle heavier loads.

Rubber Grommets are made for the Studica channel and plates and or any structure with a 14mm hole. Use it for protecting wire or as a bumper.

Specifications:

• Outside diameter: 18mm
• Inside Diameter : 11mm
• Hole fitting diameter: 14mm
• Thickness: 9mm
• Step File

• • 150mm Length
  • 3 Position
  • TJC8 FH-MC on 2 Split Ends
  • TJC8 MH-FC on single end
  • Twisted Cable
  • Colors: White, Red, Black (red in middle)
  • 24AWG Guage

·      450mm Length

·      3 position

·      TJC8 MH-FC on one end

·      TJC8 FH-MC on the other end

·      Twisted cable

·      Colors: White, Red, Black (red in middle)

·      24AWG Guage

USB Cable, Type A to Type C, Blue, 2 Meters, male to male

The JST-GH to 4 Pin Dupont Cable can be used for the VMX Controller.

The Studica Robotics XT30 Male to JST-VH cable is for use with the Servo Power Block (75006) and the FTC Power Block (70407).

The Maverick Encoder Cable for FTC will connect the Maverick DC Gear Motor to the REV Control Hub.