Includes two 5mm Bore, 10 Tooth Aluminum Pulleys and one 1M XL Timing belt.

The 100mm Slim Mecanum Wheel Set comes with 2 left and 2 right, with steel ball bearings, blue steel frame and black rollers.  The wheel comprised of 12 black rollers and is able to move in any direction. Rollers are set at 45° to the axis of rotation of the wheel.  Rollers are mounted with steel ball bearings, making the roll more fluent.

Step File

The 125mm All-Terrain Wheel Set includes two left and two right rubber wheels. They have a foam core and therefore do not require air. They grip well on smooth, hard surfaces and are perfect for travel on uneven surfaces where you may have mulch, sand, dirt, or gravel. They are designed and manufactured by Studica to work with the Studica Robotics Building platform and other building sets. The All-Terrain wheels have been tested up to 40kg (88 lbs) using all four wheels.

Specifications,

• 2 Left Wheels and 2 Right Wheels
• Diameter: 125mm Width:
• 47.1mm
• Step files

These round groove pulleys are also referred to as U groove pulleys. They are made of 6061-T6 Aluminum with a D-Shaft hole through of 6mm, and 2 set screws for ultimate strength. Use it with the 5mm Round Belt and for gearing up or down combine them with the other round groove pulleys that range from 10mm to 60mm.

Specifications:

• Material: 6061-T6 Aluminum
• Bore: 6mm
• Belt Diameter: 20mm
• Step File

• GT2 Pulley
• Φ41.2mm*13.0mm thick
• M3 pass through holes SHCS should
• sit flush
• Bearing hole, the bearing should
• AL6061-T6
• Step File

The 38mm Omni Wheel was designed as an odometry wheel that can fit inside most channel sizes. For ease of use, three cores were designed to fit 6mm D-Shaft, 5mm Hex Shaft, and 7mm Hex Shaft. The wheel is open for easy use in any ecosystem with the provided different-sized cores.

Specifications:

• Diameter: 38mm
• Number of rollers: 8
• Body Material: Delrin
• Roller Material: TPE/TPU 80A
• Max Load: 2kg
• Weight:
   

Includes,

• 38mm Omni wheel
• 38mm 6mm D-Shaft Hub, pre-installed
• 38mm 5mm Hex Shaft Hub
• 38mm 7mm Hex Shaft

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

Specifcation:

• Stainless Steel
• 70mm length
• 6mm OD
• 5.5mm to flat
• Step File

Specifications:

• Material: 6061-T6 Aluminum
• Thickness: 6mm
• Step File

Made of aluminum, the Studica Clamping Shaft Hub is used with flex and drive wheels 

Specifcation:

• Material: 6061-T6 Aluminum
• 6mm ID
• Hole pattern for connecting to structure
• Step File 

The Motor Mount Plate is used with the Maverick 12V DC Gear Motor  (Part# 75001) to attach it inside the anyone of the U Channels 76010 to 76018. This is an example of a chassis with 4 motors mounted inside the U-Channel using a Motor Mounting Plate. 

• Step File

The Studica Slide Rail is made of light weight aluminum, is 24mm wide, and is perfect for building a multi-stage slide system. Closed length is 384m, with a 240mm stroke, creating a 624mm extended length. 

• Width: 24mm
• Height: 7.2mm
• Length: 384mm
• Stroke: 240mm
• Extendended length: 624mm
• Material: 6061 Aluminum
• Step files

The Small Thrust Ball Bearing is used for vertical and axial loads to withstand heavy loads. These ball bearings have track grooves on the upper and lower track boards to reduce friction. Use these with structure for any hole where an axial load will be applied.

Specifications:

• Bore Diameter - 6mm
• Outer Diameter - 12mm
• Outer Diameter Pilot: 11.8mm
• Ball Diameter: 2mm
• Height - 4.5mm
• Material: Chrome Steel GCr15
• Step file

The Studica Smart Robot Servo Programmer is used for programming the Studica Multi-Model Smart Servo Motor and for testing other standard Servos. Use it to program the Studica Servo to switch between continuous mode, standard mode, or any custom angular mode.  

Specifications:

• Requires 6 Volt battery pack with TJC8 connector or use the Studica 6V DC Battery Holder.
• Programming setting modes
  • Standard
  • Continuous
  • Angular

The 250mm Rail and Block Set will provide precision and low friction sliding for all your robot applications.

Specifications:

• 9mm wide x 250mm Stainless Steel Guide Rail
• Ball Bearing Block
• Step File

These round groove pulleys are also referred to as U groove pulleys. They are made of 6061-T6 Aluminum with a D-Shaft hole through of 6mm, and 2 set screws for ultimate strength. Use it with the 5mm Round Belt and for gearing up or down combine them with the other round groove pulleys that range from 10mm to 60mm.

Specifications:

• Material: 6061-T6 Aluminum
• Bore: 6mm
• Belt Diameter: 30mm
• Step File

64 Tooth 5mm Pitch GT2
Belt 9mm wide
Rubber

Black

• Φ20.0mm*8.0mm thick
• 2*M3 thread for M3 SHCS on the clamp side
• Φ6.0mm D hole
• AL6061-T6
• Step File

The 6mm diameter D -Shaft is made of stainless steel and is used throughout our building system as drive components. The D-Shaft profile is used with pulleys, gears and hubs when tightening the set screws and creating a non-slip connection.

Specifcation:

• Stainless Steel
• 96mm length
• 6mm OD
• 5.5mm to flat
• Step File

Use it to power the Studica Smart Robot Servo Programmer or any other device requiring 6V output and a TJC8 connector. 

Specifications:

• 6V Output
• On/Off Power switch
• TJC8 connector
• Uses 4 x 1.5V AA Batteries (not included)

Used with Studica Omni and Mecanum wheels for a strong axel hold.

Specifications:

• Material: 6061-T6 Aluminum
• Color: Blue
• Step File

The Studica Face Bearing Block can be mounted on any  Studica channel and bracket providing which will allow for a 6mm ID through hole for 6mm shafts (axles). It has a permanently installed Standard Sealed Bearing. Has 8 x M3 tapped through holes for easy mounting.

• Step File

The Studica Servo Spline Gear is a 30 Tooth Gear with a 25 Tooth Spline. It is used with the Studica Multi-Mode Smart Servo or Studica Multi-Mode Smart Servo 200.

Specifications:

• Material: Steel Hardened, Zinc plated
• Step File

The 400mm Rail and Block Set will provide precision and low friction sliding for all your robot applications.

Specifications:

• 9mm wide x 400mm Stainless Steel Guide Rail
• Ball Bearing Block